Skip to content

Elipse Knowledgebase

  • Home
  • English (US)English (US)
    • Português do BrasilPortuguês do Brasil

Category: IODriver / IOServer

Communication established correctly in E3Studio, but fails at run time.

25 de March de 20197 de May de 2019Elipse SoftwareLeave a Comment on Communication established correctly in E3Studio, but fails at run time.

Question: Why does the communication properly established via E3Studio fail at run time? Solution: A few reasons for communication failures at run time are: 1. The hardkey or softkey was…

Read More

KB-31534: Working with an I/O tag’s deadband.

25 de March de 20195 de July de 2019Elipse SoftwareLeave a Comment on KB-31534: Working with an I/O tag’s deadband.

Question: How does a tag’s deadband (PercentDeadband property) work? Does it depend on a configured scale, or is it calculated from each value updated in the tag? Solution: If you…

Read More

KB-27407: I/O Blocks.

25 de March de 20195 de July de 2019Elipse SoftwareLeave a Comment on KB-27407: I/O Blocks.

Question: What are I/O Blocks for? Solution: I/O Blocks optimize the communication. For example, when there is a sequence of addresses in the device, the I/O Block will read all…

Read More

KB-31574: Detecting communication failure via Elipse E3.

25 de March de 20195 de July de 2019Elipse SoftwareLeave a Comment on KB-31574: Detecting communication failure via Elipse E3.

Question: How can I detect any communication failure via Elipse E3? Solution: Any communication failure can be handled via scripts the Driver’s OnCommError and OnCommErrorEx, which are always fired whenever…

Read More

Working with bits in an I/O Tag.

25 de March de 20194 de October de 2021Elipse SoftwareLeave a Comment on Working with bits in an I/O Tag.

Question: How can I access (read/write) the bits in an I/O tag? Answer: To do so, you must enable the tag’s UseBitFields property. That way, these bits can be accessed…

Read More

Working with scales in an I/O Tag.

25 de March de 20195 de July de 2019Elipse SoftwareLeave a Comment on Working with scales in an I/O Tag.

Question: How can I apply a scale in an I/O Tag? Can I retrieve, via scale, its value without the scale? Solution: To use a value scale in an I/O…

Read More

KB-31875: Prioritizing tag update.

25 de March de 20195 de July de 2019Elipse SoftwareLeave a Comment on KB-31875: Prioritizing tag update.

Question: How can I make some tags be updated before others in Elipse E3? Solution: Usually, the driver will require each tag’s value periodically, according to the tag’s Scan property.…

Read More

KB-32965: Difference between the I/O tag’s Value and RawValue properties.

25 de March de 201910 de October de 2023Elipse SoftwareLeave a Comment on KB-32965: Difference between the I/O tag’s Value and RawValue properties.

Question: What is the difference between the I/O tag’s Value and RawValue properties in Elipse E3? Solution: The difference between them is: Value: shows the formatted value (in the chosen…

Read More

KB-65789: I/O points consumption on offline mode when using an XObject.

25 de March de 20193 de June de 2019Délio DaminLeave a Comment on KB-65789: I/O points consumption on offline mode when using an XObject.

Question: As seen below, I have an XObject with one driver and three I/O tags:     The driver starts on offline mode, and its parameterization (IP, port, and network…

Read More

Consumption of I/O points in the license when N/B parameters are edited at run time.

25 de March de 20195 de July de 2019Elipse SoftwareLeave a Comment on Consumption of I/O points in the license when N/B parameters are edited at run time.

Question: If an IOTag’s N/B parameters are edited at run time, will more I/O licenses be consumed? Solution: Yes. By default, both Elipse E3 and Elipse SCADA consume an I/O…

Read More

Posts navigation

Previous 1 2 3 … 5 Next

Categories

Search by Category

© 2025 Elipse Knowledgebase | Elipse Software - Todos os Direitos Reservados.